15913833437@139.com
15913833437
|
- 起订量 (千克)价格
- 25-100￥29.9 /千克
- ≥100￥29 /千克
- 品牌：兰蒂奇
- 货号：01
- 发布日期： 2024-06-01
- 更新日期： 2025-05-07
| 品牌 | 兰蒂奇 |
| 货号 | 01 |
| 用途 | 汽车配件 电子配件 |
| 牌号 | S CV200K 3796BK |
| 型号 | S CV200K 3796BK |
| 品名 | PA6 |
| 外形尺寸 | 25 |
| 生产企业 | Radilon |
| 是否进口 | 是 |
玻璃纤维PA6 Radilon S CV200K 3796BK
PA6又称尼龙6;英文名:Polyamide，缩写nylon6。同PA66相比，它的熔点较低，而且工艺温度范围很宽。它的抗冲击性和抗溶解性比尼龙66塑料要好,但吸湿性也更强。
优点：1、具高抗张强度；2、耐韧、耐冲击性特优；3、自润性、耐磨性佳、耐药品性优；4、低温特性佳；
收缩率:0.7%-2.0%;或者加了30%的玻璃纤维，收缩率为0.3%-0.8%;如果提供的温度超过60℃℃，制品应该为逐渐冷却;逐渐冷却可降低成型后收缩。即制品表现为更好的尺寸稳定性和小的内应力;建议采用蒸汽法;尼龙塑料制品可以通过熔焊液剂来检查应力。
浇口系统:点式，潜伏式，片式和直浇口都可以;建议使用盲孔和浇口窝来段冷料点;可使用热流道;由于熔料可加工温度范围窄，热流道应提供闭环温度控制。由于尼龙6的凝固时间很短，因此浇口的位置非常重要。浇口孔径不要小于0.5"。如果使用热流道，浇口尺寸应比使用常规流道小一些，因为热流道能够帮助阻止材料过早凝固。如果用潜入式浇口，浇口的最小直径应当是0.75mm。料筒设备:标准螺杆，特殊几何尺寸有较高塑化能力;止逆环，直通喷嘴;对加入了玻璃纤维的增强材料，则需要高耐磨的双金属料筒
5、具自熄性
用途：电子电器：连接器、卷线轴、计时器、护盖断路器、开关壳座
汽车： 散热风扇、门把、油箱盖、进气隔栅、水箱护盖、灯座
工业零件：椅座、自行车输框、溜冰鞋底座、纺织梭、踏板、滑输
易吸湿，需干燥，含水量不得超过0.3%。成型收缩范围及收缩率大，方向性明显，易发生缩孔、变形等。由于热膨胀和吸水性所致的尺寸精度不够。
PA6应用范围
工业生产中泛用于制造轴承、圆齿轮、凸轮、伞齿轮、各种滚子、滑轮、泵叶轮、风扇叶片、蜗轮、
推进器、螺钉、螺母、垫片、高压密封圈、耐油密封垫片、耐油容器、外壳、软管、电缆护套、剪切机
滑轮套、牛头刨床滑块、电磁分配阀座、冷陈设备、衬垫、轴承保持架、汽车和拖拉机上各种输油管、
活塞、绳索、传动皮带，纺织机械工业设备零雾料，以及日用品和包装薄膜等。
RADILON® A NST6650HSL
High Impact Nylon 66 Exceptional Toughness in dry as molded state and at low temperatures Heat Stable
More ?
RADILON® A NST6650L
High Impact Nylon 66 Exceptional Toughness in dry as molded state and at low temperatures
More ?
RADILON® A NST66G33HSL
High Impact Nylon 66 reinforced with 33% glass fiber Heat Stable
More ?
RADILON® A NST66G14HSL
High Impact Nylon 6 reinforced with 14% glass fiber Heat Stabilized
More ?
RADILON A 24E 100 NAT
PA66 low viscosity extrusion grade. Natural colour
More ?
RADILON A 38 100 NAT
PA66 extrusion grade for tubes, profiles and sheets. Natural colour
More ?
RADILON A 42 100 NAT
PA66 extrusion grade fot tubes, profiles and sheets. Natural colour
More ?
RADILON A BF 990 GRI
PA66 injection moulding grade with molybdenum disulfide. Enhanched friction properties. Natural grey colour
More ?
RADILON A CF300K 333 NER (29066)
PA66 30% Carbon fiber reinforced injection moulding grade. High stiffness and high conductivity. Black colour
More ?
RADILON A CP300K 338 NER
PA66 30% Mineral filled injection moulding grade. Good dimensional stability, good surface finish and low warpage. Heat stabilized. Black colour
More ?
RADILON A CP400 333 NER
PA66 40% Mineral filled injection moulding grade. Good dimensional stability, good surface finish and low warpage. Black colour
More ?
RADILON A CV300 100 NAT (16091)
PA66 30% Glass beads filled injection moulding grade. Good dimensional stability, excellent surface finish and low warpage. Natural colour.
More ?
RADILON A CV500 100 NAT
PA66 50% Glass beads filled injection moulding grade. Good dimensional stability, excellent surface finish and low warpage. Natural colour
More ?
RADILON A ECP3808 339 NER
PA66 30% Mineral filled injection moulding grade. Improved impact strength, high dimensional stability. Black colour
More ?
| PHYSICAL |
Dry
|
Conditioned
|
Unit
|
Test Method
|
| Density |
1.35
|
--
|
g/cm3
|
ISO 1183 |
| Molding Shrinkage 4 | ISO 294-4 | |||
| Across Flow |
1.0
|
--
|
%
|
|
| Flow |
0.30
|
--
|
%
|
|
| Water Absorption | ISO 62 | |||
| Saturation, 73°F, 0.0787 in |
6.2
|
--
|
%
|
|
| Equilibrium, 73°F, 0.0787 in, 50% RH |
1.6
|
--
|
%
|
| MECHANICAL |
Dry
|
Conditioned
|
Unit
|
Test Method
|
| Tensile Modulus |
1.38E+6
|
1.09E+6
|
psi
|
ISO 527-1/1A/1 |
| Tensile Stress (Break) |
27600
|
18900
|
psi
|
ISO 527-2/1A/5 |
| Tensile Strain (Break) |
3.5
|
6.5
|
%
|
ISO 527-2/1A/5 |
| Flexural Modulus 5 |
1.25E+6
|
--
|
psi
|
ISO 178 |
| Flexural Stress 5 |
41300
|
--
|
psi
|
ISO 178 |
| IMPACT |
Dry
|
Conditioned
|
Unit
|
Test Method
|
| Charpy Notched Impact Strength | ISO 179/1eA | |||
| -22°F |
5.2
|
--
|
ft·lb/in2
|
|
| 73°F |
6.2
|
9.5
|
ft·lb/in2
|
|
| Charpy Unnotched Impact Strength | ISO 179/1eU | |||
| -22°F |
33
|
--
|
ft·lb/in2
|
|
| 73°F |
43
|
48
|
ft·lb/in2
|
| THERMAL |
Dry
|
Conditioned
|
Unit
|
Test Method
|
| Deflection Temperature Under Load | ||||
| 66 psi, Unannealed |
482
|
--
|
°F
|
ISO 75-2/Bf |
| 264 psi, Unannealed |
464
|
--
|
°F
|
ISO 75-2/Af |
| Vicat Softening Temperature |
482
|
--
|
°F
|
ISO 306/B50 |
| Melting Temperature 6 |
500
|
--
|
°F
|
ISO 11357-3 |
| CLTE | ISO 11359-2 | |||
| Flow : 73 to 131°F |
1.4E-5
|
--
|
in/in/°F
|
|
| Transverse : 73 to 131°F |
5.3E-5
|
--
|
in/in/°F
|
| ELECTRICAL |
Dry
|
Conditioned
|
Unit
|
Test Method
|
| Surface Resistivity 7 |
1.0E+12
|
1.0E+10
|
ohms
|
IEC 62631-3-2 |
| Volume Resistivity 7 |
1.0E+15
|
1.0E+13
|
ohms·cm
|
IEC 62631-3-1 |
| FLAMMABILITY |
Dry
|
Conditioned
|
Unit
|
Test Method
|
| Burning Rate (0.118 in) |
0.0
|
--
|
in/min
|
ISO 3795 |
| Flame Rating |
HB
|
--
|
|
UL 94 |
| Glow Wire Flammability Index (0.08 in) |
1290
|
--
|
°F
|
IEC 60695-2-12 |
| INJECTION |
Dry
|
Unit
|
|
| Drying Temperature - Desiccant Dryer |
176
|
°F
|
|
| Drying Time - Desiccant Dryer |
2.0 to 4.0
|
hr
|
|
| Dew Point - Desiccant Dryer |
< -4
|
°F
|
|
| Suggested Max Moisture |
0.10
|
%
|
|
| Processing (Melt) Temp |
536 to 572
|
°F
|
|
| Mold Temperature |
176 to 212
|
°F
|
|
| Injection Rate |
Moderate-Fast
|
|
